Flight simulator x joystick calibration4/29/2024 You'll find it in the FS Modules folder.įSVersionUsed="Microsoft Flight Simulator X",7.0Ģ.GUID= ![]() ![]() If you want me to look at the INI and tell you what you've done, please just paste its contents into a message here. There's no way it can detect any difference in any case. If you think they are not being restored on restarting FSX, then maybe you made the synch positions when in a Profile or Aircraft Specific setting which is different from the one you then used on reloading?Ĭertainly there is no difference to FSUIPC (or FSX) whether FSX is restarted or the computer is restarted. They cannot get lost, and are read during initialisation, when entering the Calibration dialogue again, and when changing aircraft - the last matters if they are specific to one aircraft or one profile. When you press OK to exit the options dialogue, all those synch positions are recorded in the section of the FSUIPC4.INI file. Regarding the square adapter, to properly install the plug into the 12FG transmitter port requires the neck of the plug to be bent back slightly for it to seat properly.I press Sync pos, but after restart my computer - it seems to have forgot the calculations- but not happen if only quitĪh, you mean the synch positions in Calibration, where you can have many calibration points to make throttles match better? When the cable is working correctly, the values for each active channel should appear in the neXt FS channel window and will change with each stick movement. If the jacks are reversed, the plug will fit reasonably snug on the dongle, but the adapter end will fit much looser. When installed correctly, the plug will fit snug on the dongle, as well as, the adapter. The mini audio jacks that are installed on each end of the cable, appear to be the same length and diameter, but they are not. The second problem was the connection between the USB dongle and either of the two adapters. SOLID - Device drivers installed (known USB device).īLINKING - Device drivers installed (known USB device) and connected to a powered on, USB device (transmitter). Here are the LED patterns that I observed:įLASHING - Device drivers are not installed (unknown USB device). The device name is SAILI Simulator XTR5.5+G2+FMS and the controller hardware lists the following entries:Īlso, when the USB dongle is plugged into the computer's USB port, the LED on the USB dongle will identify different modes of operation. The drivers had to be manually installed from the CONTROL PANEL > HARDWARE DEVICE tab. The problem was twofold.įirst, the drivers for the USB dongle did not install automatically when connected to the USB port. In addition, both of my transmitters, the Futaba 12FG and Hitec Eclipse 7, function with neXt FS, USB simulator cable XTR/AeroFly/FMS from HobbyKing and Windows 7. Wunderbar! The problem has been resolved. It's also important to plug in only this USB adapter and remove all other joysticks and USB simulator adapters. Do you see any channel movement in the Channel Overview? If not, it helps sometimes to pull out the USB adapter while running the neXt, wait a few seconds and plug it in again. In a Futaba transmitter you can do this in the Linkage / Function menu. If not, you should move the missing function in your transmitter to an other channel. ![]() Each function (Aileron, Elevator, Collective Pitch and Rudder) should move one slider there. Then start the neXt, press esc, go to Simulator tab, press on Calibrate Input Device and take a look at the Channel Overview window. If not, go to System - Trainer and make sure Act/Inh is ON, Teacher/Student is STUD, 12/8 Channel is 8ch and Modulation is PPM. A Futaba transmitter shows in his display 'trainer student' in the bottom right area. Mostly you don't switch on your transmitter and simply plug in the simulator cable. Make sure your transmitter is in trainer mode. All of them worked but sometimes it was necessary to change the output channels in the transmitter. ![]() But I have tested these blue USB dongle with Futaba, JR, Graupner and Spektrum transmitters. Unfortunately I don't have any experiences with the Hitec Eclipse 7.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |